Bridge ordering information below: 

*** "Brekke Bridge" is a Trademark of Bridger Products, LLC ***

New May 2022 

The original Brekke mandolin bridge has been updated with several new changes

and improvements.  The changes were made to accomadate a growing European

market and to reduce the number of inventory parts for dealers and resellers. 

The most important changes to the design are:

There are now three carved-top mandolin base sizes: Tall, Low and Ultra-low.



The new adjustment screws are 3 mm stainless set screws with 3 mm brass inserts.

(replaced the rather odd 5-40 custom inserts that were used). 

The adjustment wrench is 1.5 mm and gold colored.

A small indentation has been added to the base, between the slots, to identify the

new bases that use 3 mm screws.  

The bottom arch is full-contact rather than a two-foot design (based on the belief

that anyone who can fit a bridge can make a full-contact bridge into a two-foot bridge,

if desired).

All carved-top bridges will be shipped with radius saddles (again, because it is relatively easy to make a radius saddle flat and harder to make a flat saddle radiused).

A complete bridge package will contain: an ebony base, wedges, short and tall intonated saddles, and a 3 mm adjustment wrench. 



Ultra-Low Carved-top bridge

Adjustable Flat-Top Mandolin Bridge

As far as I know, this is the only adjustable bridge that can go low enough to work on

a Flat-top instrument.  The adjustment range is not large, but it is significant. 

There are custom versions of this bridge for: mandola, octave and

bouzouki instruments.  Please contact bridgerproducts@gmail.com for

information about custom bridges.

Ordering a Bridge

In general, we try to support your local brick and mortar music stores and luthiers. 

Instrument bridges, in particular, require proper installation to achieve their best

performance.  A good instrument set-up, done by an experienced professional, is

always recommended.  Please check for a dealer in your area. 

If there is not a dealer in your area but you have someone that you trust to work on

your instrument, we are willing to work with them to get the correct bridge for your

instrument.  Either ask them to contact us or email us thier contact information

at bridgerproducts@gmail.com and we will contact them for you. 

You may also order a bridge directly if you feel comfortable doing your own bridge

installation.  Please email us with the information listed below and we will

help you get the proper bridge.

​

To order a bridge directly from Bridger Products:

1)    Measure the height of your existing bridge at the height you prefer:

(from the top of your instrument to the top of the saddle)

2)   Email the information to:    bridgerproducts@gmail.com 

__________________________________________________________________________________________

Bridge Sizes & Cost

 

Arch-top A & F Mandolins

Complete Original Bridge:  Ebony, base, wedges, short & tall saddles, wrench:  $ 65

* All heights are approximate and change when fitting the bridge to an instrument *

* Flattening a radius saddle will reduce the height about 1/16 (.0625) inches *



( OBCT - T )    Arch-top A & F Mandolin - Tall base - radius saddles:    Adjustment Range:     .7 to 1.0 inches

( OBCT - L )     Arch-top A & F Mandolin - Low base - radius saddles:    Adjustment Range:    .6 to .9 inches

( OBCT - U )    Arch-top A & F Mandolin - Ultra-Low base - radius saddles:  Adjustment Range:  .5 to .65 inches

  

*** Ultra - low base  -  flat saddles:   Adjustment Range:  .465 to .715 inches 

Adjustable Flat-top Bridges 

Complete Flat-top Bridge:  Ebony: base, wedges, short and tall saddles, wrench:  $ 65

 

( OBFL - F )   Flat-Top Mandolin - radius saddles:    Adjustment Range:  .5 to .65 inches

*** Flat base  -  flat saddles:    Adjustment Range:  .465 to .715 inches 

Dealers        Builders        Articles

bridgerproducts@gmail.com